A pig carcass splitting station divides the dressed carcass along the spine at station 14, immediately before veterinary inspection. The cut can be made by a robotic splitting unit, a band saw or a circular saw, and the choice depends on the carcass range, the required rate and the working routine the plant can sustain. Whichever head is used, the station itself is set by rail elevation, the presentation of the carcass at the blade and the operator’s working level.
Where the splitting station sits in the pig line
Splitting follows red offal removal and hands over to veterinary inspection. The station takes a whole dressed carcass and releases two half carcasses onto the downstream route, so it changes both the handling unit and the load pattern on every rail beyond it. Two consequences follow. The inspection point must sit after the split, because the veterinarian inspects halves rather than a whole carcass. And the rail beyond the station carries a different load from the rail before it, so the transfer between the two belongs in the same scope as the splitting equipment.
The station does not decide the inspection outcome. It presents the carcass to the inspection point in the condition that point requires, and the inspection decision itself stays with the plant and its veterinary service.
Three ways to make the cut
All three approaches are built for the same station, so the comparison is about the working routine rather than about capability.
| Approach | What it suits | What it changes in the station |
|---|---|---|
| Robotic splitting unit | A steady rate with a narrow carcass range and a repeatable hanging position | Adds a robot work area, guarding, controls and sanitation access, and requires a defined conveyor interface at both ends |
| Band saw, hand-guided | A variable carcass range at a moderate rate, where the operator follows the spine | Needs a balance or spring support, a blade service point and a working platform |
| Circular saw, hand-guided | A compact head for a narrow range, where the carcass is steered past a fixed blade line | Needs a support arm and a disc service routine; the clearance envelope differs from a band head |
The station page for this line describes the robotic arrangement. A hand-guided saw is quoted for plants that split a wider carcass range or run a lower rate than a robotic station justifies.
The two hand-guided heads compared
Where a hand-guided saw is the right answer, the band head and the circular head separate on the service and hygiene routine rather than on the cutting speed on paper. The table below is the detail behind the last two rows of the table above.
| Criterion | Band saw head | Circular saw head |
|---|---|---|
| Cut character | Continuous blade; the cut follows the spine with less lateral correction from the operator | Rotating disc; the operator steers the carcass past a fixed blade line |
| Blade service | Blade replacement and tensioning are routine; a broken blade stops the station until it is changed | Disc inspection and dressing; a damaged disc is replaced as a complete unit |
| Head weight and balance | Longer head, so a balance or spring support is usually required | Compact head; the balance requirement depends mainly on the support arm |
| Hygiene design | Blade guides and housings must be cleanable; bone dust and swarf collect around the guides | Guard and disc housing must be cleanable; spray deflection differs from a band head |
| Rail carriage | Head travels on a carriage matched to the rail section | Same carriage question, but the smaller head changes the clearance envelope |
Read the table as a list of questions for the supplier rather than a ranking. On a line running a narrow carcass range at a steady rate either type can be correct, and the deciding factor is usually which service routine the plant can actually perform on every shift.
The interfaces that decide whether a saw fits
| Interface | What to measure or state | Why it decides the fit |
|---|---|---|
| Rail elevation and gauge at the saw | Rail height at the splitting position from a single datum, plus the rail section and gauge | Sets the operator’s reach and the carriage the head must mount to |
| Carcass presentation | Carcass size range, hanging components in use (gambrel, hooks, spreader) and the entry and exit positions | Sets the cut capacity and the clearance needed on each side of the blade |
| Operator working level | Floor or platform height, standing space on both sides and the protective arrangement | Sets the head support and whether platform travel is in the machinery scope |
| Blade, balance and sanitation services | Power supply, blade cleaning or sterilisation point, water and drainage if used, and maintenance access | These are the items most often left out of an offer and then become site work |
What the quotation must state
| Item | Why it belongs in the written offer |
|---|---|
| Saw head model and stated cut capacity | Identifies what is supplied, independently of the brochure photograph |
| Balance or spring support | Determines operator effort and whether a support structure is in scope |
| Rail carriage and bracket interface | Defines who supplies and fits the connection to the overhead rail |
| Blade specification and initial spares | Blades are consumables; the offer should state what arrives with the machine |
| Power supply and control arrangement | Confirms the electrical boundary against the local distribution package |
| Wash-down and blade sanitation provision | Needed for the plant hygiene review before commissioning |
| Buyer-supplied items | Lists supports, civil work, utilities and approvals that are not in the machinery price |
Scope note: dimensions and capacities for a specific saw are established in the project proposal against the measured station. A photograph or a general catalogue entry does not establish them.
Questions to put in the equipment request
- What carcass size range and hanging arrangement must the saw accept?
- What are the rail elevation and gauge at the splitting position, measured from one datum?
- Does the operator stand on the floor or on a platform, and what travel does that platform need?
- Which saw head, support and carriage scope is being quoted, and which items remain with the buyer?
- How does each half carcass leave the station, and where does inspection sit relative to that route?
Equipment video reference
The station footage shows a suspended pig carcass at the splitting position and the relationship between the saw assembly, the hanging route and the work area. Watch where the operator stands and how much clear space the blade needs.
Locate the station within the pig slaughter process and review the inspection conveyor connections that follow the cut. The equipment selection page lists the other machine types in this line.
Pig carcass splitting saw price and supply questions
What determines the price of a pig carcass splitting saw?
Price follows the saw head type, the balance or spring support, the rail carriage and the blade package. Whether a platform and its travel are included also changes the figure, and so does the hygiene design of the head housing and the blade guides. A robotic splitting station is quoted separately, because the robot cell, guarding and controls form a different scope.
Is a splitting saw available for sale on its own?
Yes. A single splitting saw can be supplied for sale separately. It is quoted with the rail carriage and balance system when the overhead arrangement is part of the scope, because a saw head without a carriage cannot be mounted on the line.
What do you need to quote a splitting saw?
Carcass size range, cuts per hour, rail elevation and gauge, the hanging components in use, the power supply and the operator working level. A section drawing of the station is more useful than a written description.
Confirm the splitting-saw quotation scope
- Selection basis: provide the carcass size range and the required cuts per hour so the proposed head can be checked against a stated basis.
- Station geometry: mark rail elevation, gauge, operator level and platform travel on the station drawing.
- Included items: ask the offer to list the head, carriage, balance support, blade package, power connection and cleaning provision.
Request a splitting-saw quotation
Check the inspection conveyor interface that follows the saw. The splitting station footage shows the working position.