A small scale pig slaughterhouse is defined less by tonnage than by how the work is organised: one shift, a crew that can be counted on two hands, and a plant that kills and chills on the same site but does not cut or further process. That combination decides the equipment far more than a head count does, because it removes the justification for automation while leaving every hygiene and inspection requirement in place.
What small scale means in a pig plant
Three working tiers cover most enquiries we receive. Read them as planning references rather than standard products: the boundaries move with carcass weight, shift length and how much of the killing floor one crew is expected to cover on its own.
10–25head per day
- Stunning pen or a simple three-point restrainer
- Bleeding on a single rail or a fixed stand
- Scalding tub, dehairing by hand and by drum
- Splitting with a hand-guided saw
- Crew of three to five
25–60head per day
- Three-point stunning conveyor or a stunning pen feeding a bleeding conveyor
- Scalding machine with a spiral dehairer
- Overhead chain from dehairing to the splitting station
- Hand-guided splitting saw with a support
- Crew of six to ten
60–120head per day
- Continuous overhead line across the killing floor
- Inspection conveyor for carcass and red offal
- Splitting saw on a rail carriage, or a robotic head
- Chilling tunnel sized to the shift output
- Crew of ten to fifteen
If your figure sits between two tiers, the deciding question is not the head count but whether the crew can keep the chain moving without stopping to carry a carcass by hand. A line that stalls for handling loses more than a line that is slightly oversized.
The stations that cannot be simplified
Cutting cost in a small plant works only where the cut does not remove a hygiene or welfare control. Four items stay whatever the size of the plant:
- Stunning and bleeding. The method must match the species and the market, and the bleed time must be controlled rather than judged by eye. A halal line changes the method, not the requirement.
- Scalding temperature and time control. Scalding is the step that makes dehairing possible and also the step that can fix dirt onto the skin. Temperature and dwell have to be held and recorded, so a thermometer and a timer belong in the scope even on the smallest line.
- Separation of the carcass from the floor. Once the carcass is opened, it cannot be carried or rested at floor level. This is what makes an overhead rail or a hoist non-negotiable, and it is also why the rail elevation and the operator’s working level have to be set together.
- Access for veterinary inspection. The inspection point needs light, space and a presentation of the carcass that the inspector can actually read. On a small line this is usually a widening of the rail rather than a separate conveyor.
Where a small plant should spend first
Budgets for this size of plant are always tight, and the order below is the one that repays itself earliest. It is also the order in which a later expansion is easiest to absorb.
- Overhead rail and the dehairing-to-splitting transfer. Everything downstream depends on the carcass being presented at a workable height. This is the item that is hardest to retrofit, because it fixes the building’s clear height and the drainage falls.
- Scalding and dehairing. The pair sets the skin quality and the water and heat demand of the whole plant. Undersizing here shows up as a second pass on every carcass.
- Splitting. A hand-guided saw is the correct answer at this scale; a robotic head only earns its place when the rate and the carcass range are both steady.
- Chilling. Sized to one shift’s output, not to a peak day. An undersized chiller forces a second shift or a hot-boning decision that the plant did not plan for.
What can wait: automatic carcass washers, mechanised offal handling, and any control system beyond start-stop and temperature recording. They are worth having, but they are not what stops a small plant from opening.
Building and utility questions to settle before the equipment
These are the items that most often arrive late in a small project and force a redesign. None of them can be answered by the equipment supplier alone.
| Item | What has to be fixed first | Why it changes the equipment |
|---|---|---|
| Clear height | The height from finished floor to the lowest obstruction above the rail | Sets the rail elevation, and with it the working level at every station and the type of hoist that will fit |
| Floor and falls | Slope, gullies and the position of the blood and scalding drains | Determines where the scalding unit and the dehairing machine can stand without a puddle trail across the clean side |
| Hot water and steam | Source, capacity and recovery rate across the shift | Decides whether scalding is heated directly or through a heat exchanger, and the size of the buffer |
| Power supply | Voltage, phases and the rating available at the killing floor | Fixes motor starting, cable routes and whether a control cabinet needs its own supply |
| Effluent | Volume and load the discharge consent allows | Limits water use per head and may rule out a continuous overflow scalding arrangement |
| Separation of clean and dirty routes | Where staff, carcasses and waste cross the floor | Often decides the layout before any machine is chosen, and a small building makes the crossing harder to avoid |
What to send us for a small scale quotation
A quotation for this size of plant can be turned round quickly if the brief carries six things:
- Head per day and the shift length you intend to run, plus the carcass weight range.
- Whether the plant is halal or conventional, and the stunning method you have chosen.
- A floor plan with clear height, or the building dimensions if a plan does not exist yet.
- Where the chiller sits relative to the killing floor, and whether cutting happens on site.
- The water, power and effluent limits you already know about.
- Whether the offer should cover the overhead rail and its support structure, or only the machines.
Send those and the reply separates the machinery from the steelwork, so you can see which part of the figure is the line and which part is the building interface.
Small scale pig line: price and supply questions
How much does a small scale pig slaughterhouse cost?
Cost is driven by the overhead rail and its support structure, the scalding and dehairing pair, the splitting arrangement and the chiller. A quotation is built from head per day, carcass weight range and the clear height of the building, so two plants with the same daily figure can land far apart. Send the shift length and a floor plan and the offer will separate machinery from steelwork.
What is the smallest pig slaughter line you can supply for sale?
A single-rail arrangement for a very small daily figure is available for sale on its own, without a conveyor chain. It covers stunning, bleeding, scalding, dehairing and a splitting position, and it is quoted station by station so a plant can add the chain later rather than buy it up front.
Can a small pig plant be expanded later without replacing the line?
Yes, if the rail elevation and the building clear height are set for the larger line from the start. The usual upgrade path is to add the overhead chain, then the inspection conveyor, then a second splitting position. Retrofitting the rail height after the floor and drains are in is the change that costs the most.
Is a robotic splitting unit worth it on a small line?
Usually not. A robotic head earns its place when the rate and the carcass range are both steady enough to keep it loaded. Below that, a hand-guided band or circular saw gives the same cut with a service routine the crew can perform itself.
Send the brief for a small scale pig line
- Rate: head per day, shift length and carcass weight range.
- Method: halal or conventional, and the stunning method chosen.
- Building: floor plan with clear height, or the dimensions if there is no plan yet.
Request a small scale line quotation
Continue with the pig slaughterhouse equipment list, the 21-stage process route, or the quotation and cost breakdown.