A pig carcass hoist lifts the dressed carcass from the dehairing discharge up to the overhead rail. It works between dehairing and pre-drying, so the fit is set by the lift stroke at the pick-up point and the rail elevation at discharge. A hoist that suits one of those levels can still fail the other, which is why the two are measured together.
Where the carcass hoist sits in the pig line
The hoist belongs to the dehairing and carcass-hoisting station. It takes the carcass off the dehairing position and hands it to the overhead rail that carries the rest of the process. Everything downstream of that handoff is rail work, so the hoist is the point where floor-level handling becomes suspended handling.
The video of a working installation stops at that transfer. The rail beyond the discharge point stays with the line design, which means the receiving rail, its curves and its elevation are a separate decision from the hoist itself.
Lift stroke, pick-up level and discharge rail
| Interface | What to measure or state | Why it decides the fit |
|---|---|---|
| Pick-up level | Height of the dehairing discharge position from a single datum, and how the carcass is presented there | Sets the lower end of the lift stroke and the entry geometry |
| Lift stroke | Required travel between pick-up and discharge, including any clearance needed to lift clear of the dehairing frame | Sets the hoist size; a short-stroke unit cannot be extended on site |
| Discharge rail elevation and gauge | Rail height at discharge, rail section and gauge, and the direction the carcass must face | Sets the upper end of the stroke and the handoff fitting |
| Clear height above the floor | Available headroom over the whole lift path, not only at the two end points | Determines whether the hoist and the suspended load fit the building |
| Carcass weight range and hanging components | Weight range, gambrel or hook type, and any spreader in use | Sets the rated load and the attachment at both ends |
The hoist-to-rail handoff
Most disputes on a hoist order come from the handoff rather than the machine. Four points should be settled before the offer is compared.
- Who supplies the receiving rail. The rail, its curves, its supports and its switches are either machinery scope or site scope, and the offer should say which.
- The elevation change at the transfer. Any rise or fall between the discharge position and the first rail support has to be shown on one drawing, from one datum.
- The operator position. Where the operator stands during the lift, and what access is needed around a suspended moving load.
- Control and interlocks. How the hoist is started and stopped, and whether it interlocks with the dehairing machine or the rail ahead of it.
What the quotation must state
| Item | Why it belongs in the written offer |
|---|---|
| Hoist model and rated load | Identifies the machine and its stated basis, independent of the photograph |
| Lift stroke and travel limits | Confirms the two measured levels are both inside the machine’s range |
| Drive and control arrangement | Fixes the boundary against the local electrical package |
| Rail interface at discharge | States whether the receiving rail and its fittings are included |
| Safety features | Over-travel limits, braking and any guarding, for the plant safety review |
| Support structure and fixings | Distinguishes machinery from building steelwork before pricing is compared |
| Buyer-supplied items | Lists supports, civil work, utilities and approvals excluded from the machinery price |
Scope note: capacity and stroke for a specific hoist are established in the project proposal against the measured building and rail. A brochure image does not establish either.
Questions to put in the equipment request
- What carcass weight range and hanging components must the hoist handle?
- What are the measured pick-up level and discharge rail elevation, taken from one datum?
- Which hanging components and which part of the receiving rail are retained or supplied?
- Who provides the support structure, the power and control connection, and the access arrangement?
- How will the hoist and the receiving rail be checked together before the line runs?
Equipment video references
The installation footage shows the hoisting and overhead-transfer arrangement on a working pig line. Follow the carcass through the transfer area and compare the receiving rail, the hanging geometry and the nearby equipment with the heights available at your own station.
Continue with the overhead rail and carcass transfer guide and the dehairing machine configuration that feeds the hoist.
Pig carcass hoist price and supply questions
What determines the price of a pig carcass hoist?
Price depends on the rated load, the lift stroke, the drive arrangement and the rail interface at discharge. The control set and the safety features also change the figure, and so does whether the receiving rail is inside the machinery scope.
Is a carcass hoist available for sale on its own?
Yes. A single hoist can be supplied for sale separately. It is quoted together with the receiving rail and its fittings when the overhead layout is part of the scope, because the handoff has to match the rail the plant will run.
What do you need to quote a hoist?
Carcass weight range, pick-up level and discharge rail elevation from one datum, rail gauge at both ends, clear height along the lift path, power supply and the position of the next station.
Confirm the carcass-hoist quotation scope
- Load and hanging arrangement: state the carcass weight range and list the gambrels, hooks or spreaders to be retained or supplied.
- Building and rail geometry: show pick-up level and discharge rail elevation from one datum, with the clear height along the lift path.
- Included items: ask the offer to separate the hoist, the receiving rail, the support structure and the electrical connection.
Request a carcass-hoist quotation
Continue with the rail-transfer planning guide and the hoisting station footage.